48V 60V 72V 50A 3000W Brushless Motor Controller with Speed Display LCD Meter for Electric Scooter Tricycle Motorcycle E-Bike

48V 60V 72V 50A 3000W Brushless Motor Controller with LCD Instrument SetProduct List: One controller + one instrument1) Instrument Panel Connector1: Negative Wire2: Positive Wire3: Headlight Wire4: One-Way Connector5: Left Turn Wire6: Right Turn Wire2) Voltage Wire1: Connector for 60V vehiclesDisconnect the connector for 48V and 72V vehicles3) Phase Wire SpeedConnect to the purple LCD instrument panel controller wireMaterial: aluminum alloyWorking voltage: 48V 60V 72VCurrent: 50ASize: 18CM9.5CM5CMMOS tube: SKST049N08Function: three-speed shift, three-speed button, anti-theft alarm, smart cruise, LCD instrument, pointer instrument, high battery brake, low battery brake, P gear selectionThe SHB0768F has a debug cable: DV (debug cable learning, throttle learning); 48V/60V/72V intelligent recognition (learning status recognition voltage 60V/72V); undervoltage (40V/50V/60V), 72V power-on self-recognition: Normal undervoltage: low-level alarm A3: low brake L; three-speed shifter (K1-low, K2-high) / three-speed pushbutton ZL: low gear 80%, medium gear 100% (default), high gear 110% (129% with wheel hub Hall effect); high gear Electric anti-skid, no running anti-skid: LCD [F3, default Yadi general protocol, maximum throttle, brake on and turn the throttle three times to switch to New Thinking/Yadi Guanneng/Emma/Tailing instrument protocol, with memory]: ABS (wheel hub secondary adjustable, default no, differential no): square wave peak [reserved 5] adjustable, current peak [+8] (it is recommended to use a higher specification MOS); sine wave peak [phase current] adjustable: no Hall can overspeed: RXD suspended wheel motor mode Hall state switching instructions[1 Sine wave to single Hall effect (one Hall effect is broken): The switch can be switched twice. The third time the switch fails, the system is forced into single Hall effect mode.2 Sine wave to no Hall effect (Hall effect ground wire failure): The switch can be switched twice. The third time the switch fails, the system is forced into no Hall effect mode.3 Single Hall effect to no Hall effect (one Hall effect is broken first, then the other Hall effect is broken / one Hall effect is broken first, then the ground wire is broken): If one Hall effect is broken first, the system is forced into no Hall effect mode, regardless of whether the second Hall effect or the Hall effect ground wire is broken.4 In all of the above situations, powering on will recheck the Hall effect status and return to the corresponding operating mode.] Current limit 40A; Soft start +13: No temperature protection; Customized for customer motors (others are not available); Push-button P position [TXD defaults to P position upon power-on. The motor is released from standstill, but only released, not forward. The brake can also be released.]低刹 L Low brake L防盗信号 A3 nti-theft signal A3TP/NCGND电门锁VCC Electric door lock VCC液晶仪表F3； LCD meter F3高刹 ； High brakeDCRXD转把信号SD； Turbo signal SD5vHCHAHB电门锁vcc: Power door lock VCC电源+: Power supply +轮动信号c: Wheel movement signal C仪表 YB : Instrument YBGND : GNDQ : Q学习线 DV : Learning cable DV按键三速 ZL : Three-speed push button ZL拨档低速K1 : Low speed shifter K1拨档高速K2 : High speed shifter K2GND : GND转把4.3V : Turbo 4.3V5V : 5V外部烧写CLK : External programming CLKGND: GND