T.F.SKYWINDINTL(TFSKYWINDINTL) | SATA3.0 to SAS hard disk adapter card 6Gbps SATA (7&15) 22Pin male to SAS 29Pin female expansion card suitable for 2.5 3.5 inch

🚀Desktop SATA to SAS Conveter Expansion Card Riser SATA (7+15)22Pin Male to SAS 29Pin Female 6G Adapter Support 2.5" 3.5" SAS HDD❗❗❗Please note when purchasing, this link has two options, divided into AB, A is a SATA to SAS single adapter card, B is a SATA to SAS adapter card and a cable, please check clearly when purchasing.🔥About this item✅Supports transmission rates of 6.0Gbps, 3.0Gbps, 1.5Gbps. Only SFF-8482 SAS hard disks are supported, and SFF-8639 U.2 hard disks are not supported.✅This adapter has built-in chip, Can convert SAS disk to the SATA interface of the common motherboard, so SATA computers can also use the SAS disk and no need any SAS raid card.✅If your SATA interface without SAS function, Connect our adapter, it can directly read/write SAS hard disk, support win7, win10, win11, lunix operating system.✅It is not recommended to connect the USB disk enclosure or cable, The USB master chipset is not adapted, incompatibility may occur.✅After conversion, the SMART of the SAS hard disk will display incomplete or no information, but it will not affect normal reading and writing.⚡Product Parameters:Product brand: T.F.SKYWINDINTLProduct model: TFSKYSAS-L01Input interface: SATA22PIN 7+15PINOutput interface: SAS 29PINProduct speed: 6GbpsProduct dimensions: Length 64.5mm * Width 23.6mm * Height 19.2mm (including connector height)Product function: Use the SATA interface of a regular computer to connect to a SAS hard driveSystem support: WIN7, WIN10, WIN11, LINUXNote: U.2 drive is not supported. If the drive is not recognized, try using a SATA interface💥Product features:This adapter card is used to transfer the server SAS hard drive to the USB interface of the ordinary motherboard, so that ordinary computers can also use the SAS hard drive. No expensive array card is needed anymore, it can be used directly.💡Things to note:PS1: Only supports 512, 4K and 4Kn sectors, 520/528 sector hard drives cannot be used.PS2: The USB to SAS easy drive cable must be connected to an external DC power supply (12V/3A) or above before it can be used.PS3: Because the SMART code of the SAS disk is different from that of the SATA disk, the code will not correspond to the SATA protocol when the SAS disk is converted to SATA. There is currently no way to solve this problem. Therefore, after the conversion, the SMART will display incomplete or no information, but it will not affect normal reading and writing.PS4: The hard drive and SSD are used for taking pictures, and they are not suitable for shipment! It is not recommended to connect the hard drive box and easy drive cable, and there is no adaptation for the USB master control. Please be careful if you have such needs. Huawei's SSDs, hard drives, and dual-arm drives cannot be used. They may be whitelisted and cannot be recognized.PS5: This easy drive cable is GEN15Gpbs, SAS mechanical hard drive is fully sufficientPS6: Because SAS hard disks are used on servers, many security protection detection and encryption mechanisms have been added. The recognition will be 10-20S slower than ordinary SATA, which is normal.PS7: Since there are many types of SAS hard disks, it is impossible to adapt them all, and some disks may not be recognized. In addition, the ones on the market are basically second-hand. Second-hand disks may have many bad sectors, bad heads and other undesirable phenomena, and may not be recognized. For example, if the power is turned on and it cries, it must be a problem with the disk, not this product.PS8: SAS hard disk does not support hot swapping, only the USB end can be hot swapped.✨Introduction to SAS hard drive✅SAS (SerialAttachedSCSI) hard disk is a high-performance storage device, and SATA (SerialATA) interface is a common data transmission standard. Although the two have different physical connection methods and protocols, SAS hard drives can be connected to SATA interfaces by using adapters.✅SAS hard disks cannot be recognized when connected to ordinary SATA interfaces. In order to use safe and stable SAS disks on ordinary computers, our company has developed a SATA to SAS hard disk converter adapter, which is specially designed so that SAS disks can be used on ordinary computers.✨Installation steps:✅ Turn off the computer and disconnect the power cord.✅Open the computer box and find the SATA7PIN slot and SATA 15PIN power cord available.✅Gently insert the adapter card into the SAS hard drive and make sure it is firmly fixed in the chassis hard drive position.✅Insert the SATA cable and SATA hard disk power cable into the adapter card, and insert the other end of the SATA data cable into the SATA port on the motherboard.✅Close the computer case again and reconnect the 220V power cord.✅Start the computer and check whether the newly added SATA device is successfully recognized in the operating system.📦Package List:A: 1xSATA to SAS adapter (B: 1xSATA to SAS adapter card + data power supply integrated cable)