Yongyw. CYCLAMI 360 Rotating Bike Computer Mount Holder For DJI OSMO Nano/360/Action 5 Pro/action 4 3/GoPro 8-13/Insta360 Go Ultra/X5/X4/X2 X3/GO 3S/Ace Pro 2/ace Camera Accessories Bike Mount for IGS Garmin XOSS

DescriptionIn theBike Computer Mount (integrated Handlebars)1x Bike Computer Mount Main Piece1x Thumb Screw2x 18mm M5 Bolts2x 18mm M4 Bolts4x Anti-Slip Rings1x 4mm Hex Wrench1x 2mm Hex Wrench1x Garmin Computer Mount1x Wahoo Computer Mount1x Bryton Computer Mount1x Giant Computer Mount2x Computer Mount ScrewsBike Computer Mount (independent Handlebars)1x Bike Computer Mount Main Piece1x Thumb Screw2x 40mm M5 Bolts2x 30mm M5 Bolts2x Long Screw Posts2x Short Screw Posts4x Anti-Slip Rings1x 4mm Hex Wrench1x 2mm Hex Wrench1x Garmin Computer Mount1x Wahoo Computer Mount1x Bryton Computer Mount1x Giant Computer Mount2x Computer Mount ScrewsSpecsBike Computer Mount (integrated Handlebars)Material:Aluminum 7075-T6, plastic, stainless steelWeight:106g (3.70z)Dimensions:187x39x33mm (7.4x1.5x1.3in)*Select M5 bolts or M4 bolts according to the screw hole size ofthe bike.The spacing between the screw holes of the Bike ComputerMount is 9-55 mm, Adijust the Bike Computer Mount to the frontor rear positions on the handlebars according to the size of theBike Computer.Bike Computer Mount (independent Handlebars)Material:Aluminum 7075-T6,plastic,stainless steelWeight:120g (4.20z)Dimensions:115x53x28.5mm(4.5x2.1x1.1in)The spacing between the holes of the Bike Computer Mount is11-39 mm.How to useBike Computer Mount (ntegrated Handlebars)1.Select a Computer Mount according to your model, theninstall onto the Bike Computer Mount, and tighten the screwswith a 2mm Hex Wrench.Tips:There are 2 mounting directions for a Computer Mountwhich can be installed on demand.Comes with 4 types of Computer Mount, suitable for manykinds of Bike Computer, you can choose one of them ondemand.2.Install the Bike Computer Mount to the front of the bike andtighten the bolts with a 4mm Hex wrench.Notes:Select M5 bolts or M4 bolts according to the screw hole sizeof the bike.The spacing between the screw holes of the Bike ComputerMount is 9-55 mm. Adjust the Bike Computer Mount to thefront or rear positions on the handlebars according to the sizeof the Bike Computer.When tightening bolts, 5Nm is recommended, or accordingto the recommended locking force value of the handlebars,Ensure that the two bolts are both locked on the BikeComputer Mount. lf there is only one bolt on the handlebar, orthe screw spacing is not sufficient for the installation of theBike Computer Mount, do not use this part, as this may causethe mount to fall.3.Install the camera (or accessories such as a flashlight) on the1/4" screw or three prong connector of the Bike ComputerMount.Notes:"lf installed on the 1/4" screw, it is recommended to use awrench to lock the mount firmly during installation."lf the three-prong connector becomes loose afterinstallation, attach Anti-Slip Rings to the connector forreinforcement.The angle of the three prong connector can be adjusted afterloosening the screws on the base.4. Install the Bike Computer on the Computer MountBike Computer Mount (Independent Handlebars)1.Select a Computer Mount according to your model, theninstall onto the Bike Computer Mount, and tighten the screwswith a 2mm Hex Wrench.Tips:There are 2 mounting directions for a Computer Mount,which can be installed as needed..Comes with 4 types of Computer Mount, to support mainlinebrands. Select which mount supports your computer.2. install the Bike Computer Mount to the front of the bike andtighten the bolts with a 4mm Hex wrench.Notes:.The Bike Computer Mount can be installed on the upper orlower side of the front of the bike as needed. Remove a pair ofbolts (upper side or lower side) from the bike, select 30mm or40mm M5 Bolts according to the length of the hole, and useeither the long or short screws and their posts to mount theaccessory over the centre of the bike, ensuring the bolts arecompletely fastened and flush with the post. lf you are notsure which bolt to use, try the long bolt first. lf the long boltdoes not fit, replace it with ashort bolt..When installing, pay attention to the direction of the bolts, sothat the bolts are installed directly into the Screw Posts.·When tightening bolts, if using a torque wrench, 5Nm isrecommended, otherwise tighten to ensure mount is firmlyattached to the handlebars.The spacing between the holes of the Bike Computer Mountis 11-39 mm. Ensure that the two bolts are both locked on the BikeComputer Mount. lf there is only one bolt hole on thehandlebar, or the spacing is not sufficient for the installationof the Bike Computer Mount, do not use the mount, as thismay fail and causedamage to your camera.3.Install the camera (or accessories such as a flashlight) on the1/4 "screw or three-prong connector of the Bike ComputerMount.Notes:*lf installed on the 1/4" screw, lock the mount firmly duringinstallation.*lf the three-prong connector becomes loose afterinstallation, attach Anti-Slip Rings for reinforcement.The angle of the three-prong connector can be adjusted afterloosening the screws on the base.4. Install the Bike Computer on the Computer Mount.