ZHIYU DC 12V 24V LED Brake Stop Light Halogen Flash Lamp Flasher Module Flash Strobe Controller 16 Mode for Car Light Control

The intellectual production of electronic products has now been newly upgraded, with 16 combinations of brake lights and fog lamp dynamic effect controllers. The 16 modes are composed of flash (burst), slow flash, breathing effect, bright dark flash, and constant light, and are suitable for rear brake lights and high brakes of 12V or 24V (working voltage range 7-30V). Control effects of lights, fog lights, independent warning lights, and strobe lights. Powerful current drive capability, can drive 90WLED lamp or 80W halogen lamp (power is the actual cumulative power, and at 12V, if 24V voltage, can drive the power to double).Installation instructions: red wire positive, white wire negative, two in and two out, the housing is marked with an arrow, the end of the arrow points to the output (connect light bulbs or LED lights). If the positive and negative poles are connected incorrectly or the direction is reversed, the light is off or always on, and the controller will not be damaged in a short time. In addition, the controller is a high-cost positive control type controller, the white line can only take one, if the original car light bulb negative "girder" (note that some car brake light is not "grounded"), you can only Use a white wire to ground and cut the other one.Common use failures and causes:1. Steady light without any dynamic effect: the positive and negative poles are reversed, or the flash mode has already passed since the power is connected first and the lamp is connected.2. Constant brightness slightly changes the effect: input and output reverse direction.3. Off: The input and output are connected reversely, and the positive and negative poles are reversed at the same time; or the output has an over-short circuit that has already burned the controller's fuse.Mode setting description: Open the cover, you can see the internal 1--4 mode setting switch, respectively, said S1, S2, S3, S4, the following table 1 represents the switch dial to the "ON" side, 0 represents the switch dial On the opposite side (the status on the baby picture is the mode of the serial number 16, all ON), and the specific mode setting is shown in the following table:NO. S1 S2 S3 S4 Mode Applies to Type1 0 0 0 0 Flash 5 times - Always LED2 1 0 0 0 Flash 10 times - Always LED3 0 1 0 0 Flash 5 times - slow flash 4 times - Always LED4 1 1 0 0 Flash 10 times - slow flash 4 times -Always LED5 0 0 1 0 Flash 5 times - Breath LED6 1 0 1 0 Flash 10 times - Breath LED7 0 1 1 0 Flash 5 times - slow flash 4 times - Breath LED8 1 1 1 0 Flash 10 times - slow flash 4 times - Breath LED9 0 0 0 1 Flash 20 times - Always LED10 1 0 0 1 Flash 20 times - Breath LED11 0 1 0 1 Continuous flash (strobe effect) LED12 1 1 0 1 Continuous slow flashing (warning effect) LED/Halogen13 0 0 1 1 Rapid changes in light and dark 4 times- Always LED/Halogen14 1 0 1 1 Rapid changes in light and dark 4 times - Breath LED/Halogen15 0 1 1 1 Slow continuous light and dark change LED/Halogen16 1 1 1 1 Pure Respiratory Effects LED/HalogenNote: The flash frequency is 4Hz, the slow flash frequency is 1.2Hz, the light and dark change frequency in modes 13 and 14 is 3Hz, the frequency of mode 15 is 1.2Hz, the breathing effect is bright and dark gradient, and one cycle is 3 seconds. Set the mode selection switch must be done after power off, and the switch must be in place! !Warning: This controller only allows professionals with a certain degree of electrical and automotive electronics to carry out the transformation and installation. If you want to install your own car, and you are not a professional, please receive a qualified auto repair. (Refurbish) Factory to find a professional to carry out the transformation and installation, if not handled properly for your car may bury potential safety hazards! Zhi Yu Electronics shall not be liable for any vehicle failure or controller failure caused by improper operation of the conversion process.The control circuit is well-designed, the choice of materials is elegant, the input is provided with a simple filter circuit, and a fragile copper foil section is designed (emergency can be blown) to avoid serious damage to the car circuit. The output adopts a high-current and low-resistance P-channel FET as a switch, and it is equipped with a shutdown anti-peak voltage absorption capacitor. The control current is large, and there is no problem of relay contact life. The main control adopts a high-reliability industrial OTP microcontroller. There is no problem with lost programs. The input and output lines use the national standard 0.75 square tin plated high-strength high-temperature silicone sheathed wire, able to withstand 200 degrees Celsius temperature and wear:Basic parameters:Operating voltage: DC 7-30VLimit voltage: DC 40V peakLoad current: 7A (LED lamp) or 6A (halogen lamp, because the cold resistance of the halogen lamp is very small, the current impact is very large, so it can drive a little lower power) At 50 degrees Celsius temperatureOperating temperature: -35 degrees Celsius to 70 degrees CelsiusShell size: 58mm36mm16mm length, width and heightWiring instructions: red line is positive, white line is negative, as shown in the figure below the housing marked with an arrow, the direction of which is the output (this side of the car lights), please be sure to identify the correct power polarity, wrong or connected Doing so will cause the lamp to have no effect (constant lighting) or no light, but will not damage the controller in a short time. If the test has no effect or does not light, stop the test immediately and check the wiring.Application examples:1. The rear brake light is equipped with flashing anti-recovery.2. The high brake light is equipped with flashing anti-recovery.3. The original car rear fog lights installed slow flash (preferably light and dark state changes), effectively improve the safety of fog driving.4. Use this controller as the control core homemade LED strobe light.5. Add triangular warning lights to the triangle.