54.6V 2A For Canon Li-Ion Battery Charger XLR 3Pin Connector 3P EU Plug AC100-240V Power Adapters For 48V Lithium Battery Pack

【Product Information】The charger comes with a connection interface: 3-pin XLR.Indicator status: green light for charging, red light for charging, green light for full charge.【Input and output】 Input: 100-240VAC, Output: 54.6V 2A, Colour: Black, Maximum power supply: 109.2W【Charger Features】 This product is suitable for lithium-ion batteries. Please note that the charging port and charger connector match, the positive and negative poles must match. The whole charger consists of black fireproof PC material housing. Adopts aluminum heat sink, can better cool the device and extend its service life.【Reliability】Multiple safety protectionShort-circuit protection, over-current protection, over-voltage protection, over-temperature protection, overload protection, over-discharge protection, cycle protection.When charging, connect the battery first, then connect the AC power supply, after fully charged, cut off the AC power supply, then unplug the battery. If you unplug the battery first when charging, especially when the charging current is large (the red light is on), it is easy to damage the charger.Charger Use and Maintenance:1.This product is suitable for lithium-ion batteries. Please pay attention to whether the charging interface and charger connector match, the positive and negative poles must match.2.Do not carry the charger with the car to avoid vibration.3.The charging time should not exceed 24 hours, and the battery should not be exhausted and recharged. Otherwise, the battery will not be able to be protected or even damaged.4.Please use the charger in a dry place, and it is strictly forbidden to get wet and rain.5.When the charger is not in use, do not always connect it to the mains. WARNINGS• To reduce the risk of injury, charge only 42V with the charger. Do not charge a non-rechargeable battery. Other types of batteries might burst, causing personal injury or other damage!• Do not disassemble the charger. Have it serviced or repaired by qualified service personnel. Incorrect assembly can result in risk of electric shock or fire.• Never use the charger as a DC power source for any electrical equipment.• Never operate a charger with a damaged cord or plug. Inspect both input and output cords for any damage before using the charger.• Never unplug a cord by pulling on the cord itself. Always grasp the plug when disconnecting the charger.• For indoor use only. Do not expose charger to rain, snow or excessive moisture.• Never charge a frozen battery.• The battery must be placed in a well-ventilated area during charging.• Do not use the charger while the equipment is operating.Note: Check maximum Amp input rating of battery. Using a charger with an amp output that is too high may cause permanent damage. input rating of battery.Usage Process1. Check the voltage and connector of your battery. 2. Connect the charger to AC, LED turns GREEN. 3. Connect DC output to Battery. LED turns RED means fast charging. 4. LED turns GREEN from RED means battery full charged. 5. Disconnect the charger from AC and battery.If your scooter is not charging, it may be for one of the following reasons:1. The charger is not compatible with your scooter.2. Your battery is damaged due to the limited life of lithium batteries. If your battery has been used for more than 12 months or has not been used for 2-3 months, your battery may be damaged.3. If the green light is on when you plug in the charger, but when you connect the scooter, the green light does not turn red but stays on and the charger does not work. This is because the positive and negative (+/-) connectors of our charger do not match the positive and negative (+/-) connectors of your scooter and your scooter has no power, you can try to connect the charger to your scooter from a different connector.4. If the green light is on when you plug in the charger, but goes off when you connect the scooter, it's because the internal short circuit of the scooter has caused the self-protection function of the charger to fail, you'd better check the scooter battery and replace it.5. Don't use for Lead Acid battery.Scope of useBattery pack, Harley electric vehicle, balance car, electric four-wheel vehicle, electric vehicle, scooter, unicycle, robot, tricycleUse and maintenance of the charger :--1. When charging, first connector to the battery, then connect to AC; after full, cut off AC, then pull the battery plug.--2. When the LED light turns green, please continue charging for 2-3 hours.--3. Please do not run out of battery power, then charger. Otherwise the battery cannot be protected or even damaged.--4. long-term shallow discharge battery, about 3 months, for a deep discharge.--5.Please confirm your battery, Because it is used to charge the lithium battery. Do not use the charger on the LiFepo4 battery, otherwise the charger will be got incredibly hot.