AM32 40A 65A 80A Brushless ESC 32-bit Speed Controller Signal Support PWM/DSHOT/Sine USB/TypeC Adjuster for RC Drone Crawler Car

AM32 40A 65A 80A Brushless ESC 32-bit Speed Controller Signal Support PWM/DSHOT/Sine USB/TypeC Adjuster for RC Drone Crawler Car40A ESCDescription:1.A new 32-bit ESC product, with a super mini size, very suitable for compact installation, it is a driving tool for various small model airplane brushless motors.2.Selected low-power MOS tube with layout placed on the same side for convenient heat dissipation and strong power.3.Mini size and high power, it is the preferred power for small aircraft, crawler, climbing vehicles.4.Integrates the BEC module (5V2A), adds overcurrent copper bars, adds thermal conductive silicone sheets, and takes all performance to a higher level.5.Supports mainstream control signals such as DSHOT and PWM, with linear at low speeds, violent at high speeds, and smooth speed regulation. It uses AM32 open-source firmware, which can be freely adjusted. It supports bidirectional operation, adjustable drag braking, sine start, and other 6.functions, and fast forward and reverse switching is very smooth.7.With a 470uF 35V capacitor to improve its working condition.8.Add low voltage protection function, improve low-speed linear performance.Specification:Item name: 32-bit ESCFirmware: AM32Master control: AT32Working voltage: 2-4S LipoMax current: 40ABEC: 5V2ASupport signal: PWM/DSHOT/Sine, etc.Applicable motor:Below the 22 seriesBoard size: 30x12mmWeight: about 4.6g65A ESCDescription:1.This AM32 ESC PRO version integrates the BEC module on board based on the original AM32 ESC, and is controlled by an adjustable switch. It provides three voltage levels of 5V/6V/7.4V and a maximum current of 5A, which can meet the additional needs of high-power peripherals.2.The PRO version has LED status indicator, reserved telemetry backhaul interface, reserved external switch pad, and on-board overcurrent copper bars. It has significant upgrades in both functionality and performance.3.The use of AM32 ESC requires the use of a matching parameter adjuster.4.Supports mainstream control signals such as DSHOT and PWM, with linear at low speeds, violent at high speeds, and smooth speed regulation. It uses AM32 open-source firmware, which can be freely adjusted. It supports bidirectional operation, adjustable drag braking, sine start, and other functions, and fast forward and reverse switching is very smooth.5.It is the preferred power for small aircraft, crawler, climbing vehicles. It is a driving tool for various small model airplane brushless motors.Specification:Item name: AM32 ESC PROType: AM32 ESCFirmware: V2.16Master control: AT32Working voltage: 2-6SMaximum current: 65ASupport signal: PWM/DSHOT/Sine, etcBEC: onboard integrationBEC parameters: 5V/6V/7.4V adjustable, 5ALED status light: supportTelemetry backhaul: supportExternal switch: supportApplicable motor:Below the 3532 MotorModule size: 52x25x7mmWeight: about 14.9g80A ESCAM32 ESC:This ESC comes pre-installed with AM32 custom firmware. It is optimized for crawler vehicles, providing verysmooth and quiet operation of your crawler, but it is also suitable for various 1/8 scale or smaller cars. It features a built-in adjustable quad-group voltage BEC, with a maximum current of 10A, for high-torque servo applications. Additionally, the included e-Switch helps avoid failures caused by harsh environments. All wires are pre-soldered.Features：1.AM32 custom firmware2.Sine wave start allows the motor to operate smoothly at ultra-low speeds3.Variable driving frequency4.Low voltage, runaway, and rotor lock protection5.High-performance 32-bit MCU6.E-switch, durable and waterproofSpecifications：Product Number : AM32 80A ESCBattery: 2~6S LipoCurrent: 80A (Continuous)BEC: Max 10A, Output 5.2/6.0/7.4/8.2V, adjustable via DIP switchElectronic switch supportedFan: Included, with reserved power plugMotor power connector: Not includedWires: Power wire 14AWGx150mm, motor end 14AWGx100mm, signal wire 200mm, electronic switch 125mmUSB LinkFor AM32/BL32, connects the ESC to a computer for configuration or firmware upgrade.Portable and easy to use, simply connect the ESC signal plug, connect the USB cable to a computer, and install the VCP driver.AM32 firmware is specifically designed for AT32 ARM processors, for controlling brushless motors (BLDC). The firmware is designed to be safe, fast, with a smooth and rapid start, and linear throttle. It is suitable for various vehicle types and flight controllers.Specification:Item Name: AM32 ESC Param ConverterLink:USBProduct size: 41.50.8cmPackage size: 4.8831cmQuantity: 1 pieceItem Name: AM32 ESC Param ConverterLink:Type-CProduct size: 2.51.10.8cmPackage size: 321cmQuantity: 1 piecePackage List:1 * 40A/65A/80A AM32 ESC（Optional）1 * Param AdapterInstructions for using the parameter adjuster :1. The 3P plug of the ESC, with the white signal wire corresponding to S and the black BEC negative wire corresponding to G, is plugged into the S and G of the tuner.2. Insert the tuner into the USB port of the computer (recommended for Windows 10), and plug in the battery for electrical tuning.3. In the FreelyRC product manual and tool library, download the parameter tuner driver (free installation on Win10) and the parameter tuning software package Esc_Cnfig_Tool_1.82 (simply unzip and do not need to install).4. After ensuring that the tuner driver is working properly (CH340 serial port device is recognized in the device manager), open the unpacked tuner software folder and run "serialPortConnector. exe"5. Operate the software in the order shown in the figure belowStep 2: Select the COM number corresponding to the tuner from the drop-down menu.Note: This COM slogan is different for each computer, so you need to choose the COM port of the corresponding tuner device on your own computer.6. Click the "Connect" button, and a "M1" button will appear in the software interface. Click on "M1".7. Start parameter tuning (Example: For bidirectional vehicle use, enable FOC)8. Press Save Settings to save, then unplug the ESC.