BEBONCOOL | NC300 Dual Hall Gamepad Console RGB Light Wireless Controller For Switch/Android/IOS/PC/Steam

1.Joystick for Windows PC, all games that natively support the controller connect and play directly. With Bluetooth receiver. Connection method: plug the receiver into the USB port of the computer host. Then press and hold the joystick sync button for about 3s, release your hand after the light is on and wait to connect to the host (wireless connection). Or use the cable to connect the joystick to the computer (wired connection). 2. The joystick is compatible with Switch, Switch connection: in the host connection interface, press and hold the synchronization button for about 3s, after the light is on, release your hand and wait for connection to the host. After connecting once, the HOME button can wake up the host and connect back.3.Compatible with games and game platforms that support HID mode on Android devices, connection method: “B ‘+’HOME”, search for Bluetooth Xbox wireless controller to connect.4.Compatible with all games that support MFI protocol on IOS devices (requires IOS 13.0 and above system) Connection method: “B ‘+’HOME”, search for Bluetooth Xbox wireless controller to connect. Connect.5. Dual-motor vibration (the text do not write HD vibration), six-axis acceleration (somatosensory). Vibration three adjustable, no weak strong, at the same time press and hold “L, R, ZL, ZR” 2 seconds, you can cycle adjust the vibration intensity. Vibration function is not available in Android and IOS. The somatosensory function can only be used in Switch series hosts.6. There are manual/automatic burst function, A/B/X/Y/L/R/ZL/ZR/keys can be set to burst. The order of opening: manual continuous hair→automatic continuous hair→closing. The speed of 5/12/20 times per second can be adjusted in three steps, Turbo+↑/Turbo+↓, speed up or slow down, vibrate to indicate the success of the adjustment. Press and hold the minus key +↓, vibrate once, you can clear the continuous hair setting of all buttons with one key.7.1000mAh Li-ion battery, USB-C charging port. Charging time is about 3 hours, and it can be used continuously for more than 10 hours under the scenario of full on light effect.8.Two programmable keys on the back to map the basic function keys (A/B/X/Y/L/ZL/R/ZR/L3/R3/Up/Down/Left/Right/+/-). Each back key can program 1-21 basic function keys. Press the M key and one M1/M2 key at the same time to enter the programming mode, then press the function keys (A/B/X/Y/L/ZL/R/ZR/L3/R3/Up/Down/Left/Right/+/-), then press the M1/M2 key to save it, the joystick will vibrate once, and the light will be restored to the normal connection state, which is the completion of the mapping of the keys programmed settings. Clear mapping: Press M key and minus key at the same time, the joystick will vibrate once to clear all the key mappings.9. Hall effect joystick, can be switched to 0 dead zone setting: Long press T+R3/L3 corresponding to the joystick aperture bright green for 1 second, switch to 0 dead zone. Press and hold T+R3/L3 again, the aperture of the corresponding joystick will light up blue for 1 second, and it will be restored to the state with dead zone. Switch to 0 dead zone set no memory function, handle shutdown after the next boot connection will be restored to the factory dead zone state (anti-drift)10. Hall effect analog trigger button, providing more precise game operation.11.RGB ambient lighting effects, 6 lighting modes (streaming phantom, breathing color changing, fixed dazzle, fixed blue, fixed red, left red, right blue) + off light effects, press the light key cycle regulation. Four brightness (25%-50%-75%-100%) adjustable: M + left button / right button plus or minus brightness.12. Connected to the state, no operation within 20 minutes, the handle automatically shutdown13. With 1.5m data cable