MJJC | Horse Racing LED Strip Light WS2811 IC DC24V RF Running Water Wave Chasing LED Tape Ribbon Lamp Synchronized for Room Decoration

 Specifications of LED Strip:Product Name: Horse Race Led Strip Light LED Type: SMD2835 LED Qty per Meter: 120Leds/m Power: 10-12W/M Working Voltage: 24V DC Protection Grade: IP20 Not Waterproof (IF you want waterproof,we can customize,inquiry to us by message) Color: Cool White(6000-6500K)/Warm White(3000-3200K)/Natrual White(4000-4500K) Control IC: WS2811, 80 IC for 10M Viewing Angle: 120° Storage Temperature: -20°to 50° PCB Width: 10mm Size ( L X W X H ): 5000/10000 x 10 x 2.5 mmProduct Parameters of Controller:Product Name: Single Color Horse Race Led Strip Controller Working Voltage: DC5-24V ( The controller dont connect to the power supply) Control Distance: Battery Type: CR2032 button cell ( Not included) Modes: 26 Different modes built-in controller. With Switch Input ( Green Wire): Turn ON,the lights running, Turn OFF, the lights backflow. Max Pixel Control:Max Control Pixels:3200pcs Pixels,if more than 3200pcs pixels,just add extra receiver or amplifier to realize sync working. Installation: With 2pcs double-side tape,anywhere to stick. 3 Keys Remote Function: ON/OFF, Model Key, Brightness UP/Down,Speed UP/DownFeatures:1. one receiver can be controlled by max 6pcs 3keys panel remotes. 2. Two receivers can be connected together,realize sync working. The wire between two receiver can be up to max 10metes for extension. 3. The controller can be work with normal switch, Turn ON/OFF by the switch without remote.It also can connect to Mihome Smart Switch to realize voice control.Sync Projects:Wire Connection Sync Working:99.99% sync (Recommend),If you want 50M sync control, just buy 2pcs x 25M full set, two controller can be connect together to make it sync working by one 3Keys remote/Normal Switch. Wireless connection sync working: Maybe has delayHow to pair Remote to the Receiver,make them working independently ?Step 1: Turn on the power supply. Step 2: Long press "Mode"keys 3seconds within 2seconds after powering ON. Step 3: Sucessfully if the led strip quick flash 3 times. 1pc receiver can be controlled by max 6pcs panel remote. We used high quality 110V 220V AC to DC 24V 200W LED power supply,100% real power output. 1pc DC24V power supply can drive max 20 meters WS2811 horse running pixel led strip. We used high quality 110V 220V AC to DC 24V 200W LED power supply,100% real power output. 1pc DC24V power supply can drive max 20 meters WS2811 horse running pixel led strip.Power Supply:Input Voltage: 100-260V AC Output Voltage: DC 24V Power: 100W / 200W We used high quality LED power supply,100% real power output. 1pc DC24V 200W power supply can drive max 20 meters WS2811 horse running pixel led strip.Q & A：Q：Why the led strip is flash ? A: The led strip have voltge-drop, just connect led strip to the power supply from two end,make it enough voltage. The detailed wiring was in this page. Q: Why only haf led strip is working, some of them not lightON ? A: Kindly increase the pixel points as following steps: *** How to setting pixels? Step 1: Turn OFF the lights Step 2: Long press "Mode" keys 5 seconds,press "Speed" keys to increase the pixels quantity, Press "Mode" keys to decrease the pixels quantity. Step 3: Press " ON/OFF" to save, Exit. Default factory setting is 80pixels,max up to 3200pixels. If you found some led strip is not light, please kindly do pixel setting as above steps.